BuildWell Colour Putty

PRODUCT 110
BuildWell Colour Putty

BuildWell colour putty is a wall putty with added advantage of shades like Pink, Yellow, Green and Off-White, especially developed to provide smooth finish on plastered surface. It contains finest quality minerals, polymers, white cement and pigments. Since it comes in shades, no painting required for interior to attain highest economy and speed. It can also be used for application areas like basement parking lot, staircase etc. as “Final Finish”.

  • Features
  • Advantages
  • Benefits
  • Other Details

Not Applicable.

  • Can be applied on Interior wall and ceiling
  • Gives smooth and glossy finish
  • Suitable for Interior
  • Save 100% of painting cost
  • Better adhesion with wall surface
  • Cost-effective
  • Ease of use at site
  • No painting required
  • Aesthetic look for ceiling and interior walls

BuildWell Colour Putty is available in 4 different colour shades

• Yellow • Off White • Pista • Pink

Application Procedure

Clean loose particles, dirt, grease and traces of foreign material from the surface, if necessary, by using sand paper or by chipping. For loose plaster areas, remove the defective material and re-plaster the area with BuildWell Ready-Mix Plaster. For ceilings/walls, which are not even, re-plaster it with BuildWell Ready-Mix plaster to make them even. Fill up any cracks in base plaster by using BuildWell Crack Filler.

Take 300 – 450 ml of clean water for 1 Kg of BuildWell Colour Putty in a clean bucket. It is very important that BuildWell Colour Putty to be added in water and not vice versa. Stir continuously by using an electric mixer or by hand to obtain a homogeneous lump-free paste. Allow the resultant paste to stand for about 10 minutes for the additives to dissolve. Re-mix again for about 2 minutes. The mixture is now ready. Use the mix within 30 minutes.

Dampen the surface to be plastered with clean water. Allow excess water to drain off. Using a steel trowel/blade, apply the above mix to a thickness of about 0.5 – 1 mm. Level and smoothen the surface. Cure the first coat lightly after it dries. Apply the second coat of 0.5 – 1 mm after the first coat has fully dried and set. In areas of high temperature and low humidity light curing for two days is recommended. The thickness of each coat should not exceed 1 mm and total plaster thickness should not exceed 2 mm. Smoother with a steel trowel, Sand paper if so desired with 600 no. of sand paper.

BuildWell Colour Putty contains only eco-friendly fillers and additives. However, being white cement based, it is alkaline and hence it is advisable to avoid direct eye and skin contact with this. In case of eye contact, flush with clean water at least for 15 minutes and seek medical help and recommend to keep it out of reach of children.

BuildWell Colour Putty is available in 30 kg bag and has a shelf life of 6 months, if stored in a cool and dry location. As temperature, humidity, water addition and other parameters vary from site to site; the above information should be treated as a general guideline.

Specifications

Technical specifications

PROPERTY TYPICAL RESULTS
Colour White
Pot life > 90Min
PH 9.2 - 10.1
Coverage 8 - 15 Sq. Ft/Kg (Depending on finish of the Wall
Recommended Mixing 300 - 450 ml of water for per kg of Wall Putty

Technical Details

PROPERTY TYPICAL RESULTS SINGAPORE HDB STD
Physical Appearance Colour -
Setting Time : Initial 270 Min > = 30 Min
Setting Time : Final 300 Min < = 600 Min
Tensile Adhesion Strength 0.84 Mpa Min 0.8 Mpa
Compression Strength 7.12 Mpa 7 - 12 Mpa
Flexural Strength 1.89 Mpa -
Water Retentivity 99.60% > = 95 %
Water Absorption 0.04 kg/m2 WO - No Requirement
W1 - 0.26 kg/m2 EN 1015 - 18 & EN 998-1-2003
W2 - 0.13 kg/m2 EN 1015 - 18 & EN 998-1-2003