BuildWell Wall Putty

PRODUCT 109
BuildWell Wall Putty

White Cement Based Wall Putty BuildWell Wall Putty is a white cement based polymer modified wall putty specially developed as a base coat to cover unevenness and pinholes on plastered, mortar wall (Internal) and ceiling to make the surface wall white and smooth and ready for primer and paint application. What is a skim coat? : A skim coat is a thin layer of cementitious plaster which is “skimmed” e.g. applied very thinly onto the interior and exterior of plastered and concrete surfaces.

  • Features
  • Advantages
  • Benefits
  • Other Details
  • Whitest putty
  • Highly water resistant
  • Strong bonding to the base plaster
  • Smooth finish
  • Durable & long lasting
  • True colour tone of the paint is maintained
  • Primer is not required
  • Protects expensive paint from dampness, peeling off and flaking
  • Excellent workability
  • Paint finish is superior
  • Reduces paint consumption
  • Avoid frequent repainting
  • Cost-effective
  • Aesthetic look for ceiling, interior and external wall
  • Ease of use at site

Not Applicable.

Application Procedure

Clean loose particles, dirt, grease and traces of foreign material from the surface, if necessary, by using sand paper or by chipping. For loose plaster areas, remove the defective material and re-plaster the area with BuildWell Ready-Mix Plaster. For ceilings/walls, which are not even, re-plaster it with Ready-Mix Plaster.. Fill up any cracks in base plaster by using BuildWell Crack Filler.

Take 300 – 400 ml of clean water for 1 Kg of BuildWell Wall Putty in a clean bucket. It is very important that Wall Putty to be added in water and not vice versa. Stir continuously by using an electric mixer or by hand to obtain a homogeneous lump-free paste. Allow the resultant paste to stand for about 10 minutes for the additives to dissolve. Re-mix again for about 2 minutes. The mixture is now ready. Use the mix within 30 minutes.

Dampen the surface to be plastered with clean water. Allow excess water to drain off. Using a steel trowel/blade, apply the above mix to a thickness of about 0.5 – 1 mm. Level and smoothen the surface. Cure the first coat lightly after it dries. Apply the second coat of 0.5 – 1 mm after the first coat has fully dried and set. In areas of high temperature and low humidity light curing for two days is recommended. The thickness of each coat should not exceed 1 mm and total plaster thickness should not exceed 2 mm. Smoothen with a steel trowel, Sand paper if so desired with 600 no. of sand paper.

BuildWell Wall Putty contains only eco-friendly fillers and additives. However, being white cement based, it is alkaline and hence it is advisable to avoid direct eye and skin contact with this. In case of eye contact, flush with clean water at least for 15 minutes and seek medical help and recommended to keep it out of children reach.

BuildWell Wall Putty is available in 1 kg, 5 kg, 20 kg, 30 kg and 40 kg bag and has a shelf life of6 months, if stored in a cool and dry location. As temperature, humidity, water addition and other parameters vary from site to site; the above information should be treated as a general guideline.

Specifications

Technical specifications

PROPERTY TYPICAL RESULTS
Colour White
Pot life > 90Min
PH 9.2 - 10.1
Coverage 8 - 15 Sq. Ft/Kg (Depending on finish of the Wall
Recommended Mixing 300 - 450 ml of water for per kg of Wall Putty

Technical Details

PROPERTY TYPICAL RESULTS SINGAPORE HDB STD
Physical Appearance White -
Setting Time : Initial 270 Min > = 30 Min
Setting Time : Final 300 Min < = 600 Min
Tensile Adhesion Strength 0.85 Mpa >0.8 Mpa
Compression Strength 7.2 Mpa 7 - 12 Mpa
Flexural Strength 1.89 Mpa -
Water Retentivity 99.60% > = 95 %
Water Absorption 0.04 kg/m2 0.13 kg/m2
WO - No Requirement EN 1015 - 18 & EN 998-1-2003
W1 - 0.40 kg/m2 EN 1015 - 18 & EN 998-1-2003
W2 - 0.20 kg/m2 EN 1015 - 18 & EN 998-1-2003